Question 1

Decoding data from the Eastron SDM630MCT-LoRa

Accepted Answer

Identifying your meter

The Eastron SDM630MCT-LoRa is a three-phase DIN rail mounted electricity meter that communicates over LoRaWAN. As illustrated by the image (left) below it will say SDM630MCT-LoRa directly to the right of the Eastron logo. The Serial Number (SN) is located below and to the right of the backlit display as displayed in the image (right).

Eastron SDM630MCT-LoRa

Connecting your meter to a LoRaWAN Network Server

The SDM630MCT-LoRa can be connected to any LoRaWAN Network Server (LNS) including TTN, TTI, Chirpstack and Loriot amongst others. cThings Cloud provide an end-to-end in-built LNS with pre-configured decoders to facilitate connecting the SDM630MCT-LoRa to your existing system. Contact us to find out more.

|| The SDM630MCT-LoRa must be setup as a Class-C device

Decoding the default data received from the SDM630MCT-LoRa

All SDM630-LoRa meters come with a default configuration pre-installed. If a custom configuration has been requested, see the section below on custom configurations.

By default, data will be sent from the SDM630MCT-LoRa every 30 minutes. Below is an example hex encoded payload that could be sent from a default configured meter (it has been conveniently separated into chunks to match the decode in the table below).

| 001435FC 01 14 443A424E 40E7A876 42C5DA1D 439449DB 43AEC439 3

Question 2

Decoding data from the Eastron SDM230-LoRa

Accepted Answer

Identifying your meter

The Eastron SDM230-LoRa is a single-phase DIN rail mounted electricity meter that communicates over LoRaWAN. As illustrated by the image (left) below it will say SDM230-LoRa to the top right of the backlit display beside the Eastron logo. The Serial Number (SN) is located on top, above the display as displayed in the image (right).

Eastron SDM230-LoRa

Connecting your meter to a LoRaWAN Network Server

The SDM230-LoRa can be connected to any LoRaWAN Network Server (LNS) including TTN, TTI, Chirpstack and Loriot amongst others. cThings Cloud provide an end-to-end in-built LNS with pre-configured decoders to facilitate connecting the SDM230-LoRa to your existing system. Contact us to find out more.

|| The SDM230-LoRa must be setup as a Class-C device

Decoding the default data received from the SDM230-LoRa

All SDM230-LoRa meters come with a default configuration pre-installed. If a custom configuration has been requested, see the section below on custom configurations.

By default, data will be sent from the SDM230-LoRa every 30 minutes. Below is an example hex encoded payload that could be sent from a default configured meter (it has been conveniently separated into chunks to match the decode in the table below).

| 01354BEC 01 14 3C83126F 436D3798 00000000 3F800000 4248320D F792

The meter will send th

Question 3

What parameters are available for the Eastron SDM630MCT-LoRa Electricity Meter?

Accepted Answer

What parameters are available for the Eastron SDM630MCT-LoRa Electricity Meter?

The following tables are a list of parameters available for the Eastron SDM630MCT-LoRa Electricity Meter.

General & Total Parameters

| Parameter | Unit | Register | | ----------- | ----------- | ----------- | | Frequency | Hz | 06 | | Total Current | A | 0A | | Neutral Current | A | 0B | | Total Power Factor| None | 0F | | Total Active Power | W | 13 | | Total Reactive Power | var | 17 | | Total apparent Power | VA | 1B | | System Phase Angle | Degrees | 1F | | Maximum Total System Power Demand | W | 20 | | Maximum Total System Reactive Power Demand | var | 21 | | Maximum Total System Apparent Power Demand | VA | 22 | | Maximum Neutral Current Demand | A | 26 | | Import Active Energy | kWh | 2D | | Export Active Energy | kWh | 2E | | Total kWh | kWh | 2F | | Import Reactive Energy | kvarh | 30 | | Export Reactive Energy | kvarh | 31 | | Total kVArh | kVArh | 32 | | Total kVAh | kVAh | 33 | | Active Energy by Algebraic Sum Method | kWh | 46 | | Reactive Energy by Algebraic Sum Method | kVArh | 47 | | Resettable Total Active Energy | kWh | 48 | | Resettable Total Reactive Energy | kvarh | 49 | | Resettable Import Active Energy | kWh | 4A | | Resettable Export Active Energy | kWh | 4B | | Resettable Import Reactive | kVArh | 4C | | Resettable Export Reactive Energy | kVArh | 4D |

Phase 1 (L1) Parameters

| Parameter | Unit | Register | | ----------- | ----------- | ----------- | | L1

Question 4

Decoding data from the Eastron SDM530-LoRa

Accepted Answer

Identifying your meter

The Eastron SDM530-LoRa is a three-phase DIN rail mounted electricity meter that communicates over LoRaWAN. As illustrated by the image (left) below it will say SDM530-LR directly to the right of the Eastron logo. The Serial Number (SN) is located on top, above the display as displayed in the image (right).

Eastron SDM530-LoRa

Connecting your meter to a LoRaWAN Network Server

The SDM530-LoRa can be connected to any LoRaWAN Network Server (LNS) including TTN, TTI, Chirpstack and Loriot amongst others. cThings Cloud provide an end-to-end in-built LNS with pre-configured decoders to facilitate connecting the SDM530-LoRa to your existing system. Contact us to find out more.

|| The SDM530-LoRa must be setup as a Class-C device

Decoding the default data received from the SDM530-LoRa

All SDM530-LoRa meters come with a default configuration pre-installed. If a custom configuration has been requested, see the section below on custom configurations.

By default, data will be sent from the SDM530-LoRa every 30 minutes. Below is an example hex encoded payload that could be sent from a default configured meter (it has been conveniently separated into chunks to match the decode in the table below).

| 001435FC 01 14 443A424E 42480000 432F0000 00000000 42C5DA1D C591

The meter will send the data in a single paylo

Question 5

How do I use the cThings Cloud API?

Accepted Answer

The cThings Cloud API provides programmatic access to functionality and data available via cThings Cloud. The cThings Cloud API is a REST API that exchanges JSON data and is protected by OAuth2. This article outlines how to request an access token from the cThings AuthServer; how to use this token to make a request to the cThings Cloud API; and provides a list of available endpoints.

Security

Your credentials

To request an access token from the cThings AuthServer you will need a username (formaly a Client ID) and a password (formaly a Client Secret).

|| You should be provided with your credentials by cThings. Please get in touch with cThings Support of you do not have credentials.

The Client ID is a UUID, e.g. xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx, and Client Secret an arbitrary alphanumeric string, e.g. xxxxxxxxxxxxxxxxxxxxxxxx.

Obtaining an Access Token

An access token can be requested from the cThings AuthServer using your credentials. The cThings AuthServer implements the OAuth2 specification, specifically the Client Credentials grant type. To request an access token, make a POST request to the following endpoint.

https://authserver.cthings.cloud/token

Include the following parameters as multipart/form-data (set the Content-Type header to multipart/form-data).

| Request Parameters | Value | | ---- | | granttype | clientcredentials | | scope | api |

Include your Client ID and Ciient Secret as a Basic Auth username and password. This is done by ge

Question 6

What parameters are available for the Eastron SDM530-LoRa Electricity Meter?

Accepted Answer

What parameters are available for the Eastron SDM530-LoRa Electricity Meter?

The following table is a list of all parameters available for the Eastron SDM530-LoRa Electricity Meter.

General & Total Parameters

| Parameter | Unit | Register | | ------ | ------ | ------ | | Frequency | Hz | 06 | | Total Current | A | 0A | | Neutral Current | A | 0B | | Total Power Factor | - | OF | | Total Active Power | W | 13 | | Total Reactive Power | VAR | 17 | | Total Apparent Power | VA | 1B | | System Phase Angle | Degrees | 1F | | Maximum Total System Power Demand | W | 20 | | Maximum Total System Reactive Power Demand | VAR | 21 | | Maximum Total System Apparent Power Demand | VA | 22 | | Import Active Energy | kWh | 26 | | Export Active Energy | kWh | 27 | | Total kWh | kWh | 28 | | Import Reactive Energy | kVArh | 29 | | Export Reactive Energy | kVArh | 2A | | Total kVArh | kVArh | 2B | | Total kVArh | kVArh | 2C | | Relay State | - | 2D | | DI-1 Count | - | 2E | | DI-2 Count | - | 2F |

Phase 1 (L1) Parameters

| Parameter | Unit | Register | | ------ | ------ | ------ | | L1-N Voltage | V | 00 | | L1-2 Voltage | V | 03 | | L1 Current | A | 07 | | L1 Power Factor | - | 0C | | L1 Active Power | W | 10 | | L1 Reactive Power | VAR | 14 | | L1 Apparent Power | VA | 18 | | L1 Phase Angle | Degrees | 1C | | Maximum L1 Current Demand | A | 23 |

Phase 2 (L2) Parameters

| Parameter | Unit | Register | | ------ | ------ | ------ | | L2-N Voltage | V | 01 | | L2-3 V

Frequently Read Articles

Browse All Categories